[Fwd: stereo.c]
Shawn Kendall (skendall++at++fullsail.com)
Wed, 21 Jan 1998 13:17:23 -0500
Shawn Kendall wrote:
> Sharon Clay wrote:
> >
> > Here it is and we'll put it back with some other updates on the web site.
>
> Ok, I got the code and compiled and it ran fine, sort of...
> I'm sure someone out there has had this problem so here goes...
> When it starts up I get a
> ->PF Notice: pfChooseFBConfig: failed to make
> configuration matching specified attributes
> PF Notice/Resource: Couldn't get a stereo window; using mono
> mode
>
> Then it runs fine if the window is small. It looses sync if the window
> is expanded. I'm assuming it's not buffering the frame correctly and as
> soon as it takes more than 1/30th of a second to draw it gets behind. I
> tried several different command-line options, i.e. mulitproc and fork X,
> but still no good (didn't think it would help anyway).
> Is there some kind of before hand graphics mode I have to set. Back in
> the olden days we had to do that on regular Indigo's.
> It also doesn't work on our Onyx2, but on the Onyx we don't get any
> crystal eyes 'flicker', just a single channel.
>
> Thanks in advance.
>
> My IMPACT configuration is:
>
> Iris Audio Processor: version A2 revision 1.1.0
> 1 195 MHZ IP28 Processor
> CPU: MIPS R10000 Processor Chip Revision: 2.6
> FPU: MIPS R10010 Floating Point Chip Revision: 0.0
> On-board serial ports: 2
> On-board bi-directional parallel port
> Data cache size: 32 Kbytes
> Instruction cache size: 32 Kbytes
> Secondary unified instruction/data cache size: 1 Mbyte
> Main memory size: 128 Mbytes
> EISA bus: adapter 0
> Integral Ethernet: ec0, version 1
> Integral SCSI controller 1: Version WD33C93B, revision D
> Integral SCSI controller 0: Version WD33C93B, revision D
> Disk drive: unit 1 on SCSI controller 0
> Graphics board: High Impact
>
> AND:
> Graphics board 0 is "IMPACTPC" graphics.
> Managed (":0.0") 1280x1024
> Product ID 0x0, 1 GE, 1 RE, 1 TRAM
> MGRAS revision 3, RA revision 5
> HQ rev A, GE11 rev B, RE4 rev A, PP1 rev A,
> VC3 rev A, CMAP rev E, MC rev D
> 19" monitor (id 0x1)
>
> Channel 0:
> Origin = (0,0)
> Video Output: 1280 pixels, 1024 lines, 72.24Hz (1280x1024_72)
>
> __________________________________________________________
>
> Shawn Kendall Full Sail Real World Education
> Lab Instructor 3300 University BLVD
> Virtual Reality Winter Park FL 32792
> skendall++at++fullsail.com http://www.fullsail.com
> __________________________________________________________
--
TTFN
__________________________________________________________
Shawn Kendall Full Sail Real World Education
Lab Instructor 3300 University BLVD
Virtual Reality Winter Park FL 32792
skendall++at++fullsail.com http://www.fullsail.com
__________________________________________________________
attached mail follows:
Date: Wed, 21 Jan 1998 13:10:10 -0500
From: Shawn Kendall
To: Sharon Clay
Subject: Re: stereo.c
> ->Could someone please send me the latest working version of stereo.c. I
> ->went to www.sgi.com/Techonology/Performer then on to Performer friends
> ->but the old link is gone. I know it's in the new 2.2 distribution but I
> ->just can't wait. :)
> ->
>
> Here it is and we'll put it back with some other updates on the web site.
Ok, I got the code and compiled and it ran fine, sort of...
When it starts up I get a
->PF Notice: pfChooseFBConfig: failed to make
configuration matching specified attributes
PF Notice/Resource: Couldn't get a stereo window; using mono
mode
Then it runs fine if the window is small. It looses sync if the window
is expanded. I'm assuming it's not buffering the frame correctly and as
soon as it takes more than 1/30th of a second to draw it gets behind. I
tried several different command-line options, i.e. mulitproc and fork X,
but still no good (didn't think it would help anyway).
Is there some kind of before hand graphics mode I have to set. Back in
the olden days we had to do that on regular Indigo's.
It also doesn't work on our Onyx2, but on the Onyx we don't get any
crystal eyes 'flicker', just a single channel.
Thanks in advance.
My IMPACT configuration is:
Iris Audio Processor: version A2 revision 1.1.0
1 195 MHZ IP28 Processor
CPU: MIPS R10000 Processor Chip Revision: 2.6
FPU: MIPS R10010 Floating Point Chip Revision: 0.0
On-board serial ports: 2
On-board bi-directional parallel port
Data cache size: 32 Kbytes
Instruction cache size: 32 Kbytes
Secondary unified instruction/data cache size: 1 Mbyte
Main memory size: 128 Mbytes
EISA bus: adapter 0
Integral Ethernet: ec0, version 1
Integral SCSI controller 1: Version WD33C93B, revision D
Integral SCSI controller 0: Version WD33C93B, revision D
Disk drive: unit 1 on SCSI controller 0
Graphics board: High Impact
AND:
Graphics board 0 is "IMPACTPC" graphics.
Managed (":0.0") 1280x1024
Product ID 0x0, 1 GE, 1 RE, 1 TRAM
MGRAS revision 3, RA revision 5
HQ rev A, GE11 rev B, RE4 rev A, PP1 rev A,
VC3 rev A, CMAP rev E, MC rev D
19" monitor (id 0x1)
Channel 0:
Origin = (0,0)
Video Output: 1280 pixels, 1024 lines, 72.24Hz (1280x1024_72)
__________________________________________________________
Shawn Kendall Full Sail Real World Education
Lab Instructor 3300 University BLVD
Virtual Reality Winter Park FL 32792
skendall++at++fullsail.com http://www.fullsail.com
__________________________________________________________
=======================================================================
List Archives, FAQ, FTP: http://www.sgi.com/Technology/Performer/
Submissions: info-performer++at++sgi.com
Admin. requests: info-performer-request++at++sgi.com
This archive was generated by hypermail 2.0b2
on Mon Aug 10 1998 - 17:56:36 PDT