I don't see this problem at all on my 2.6.11-rc4-mm1 kernel (Athlon64 proc).
# ethtool -i eth0
driver: e1000
version: 5.7.6-k2
firmware-version: N/A
bus-info: 0000:00:07.0
# ethtool -d eth0
MAC Registers
-------------
0x00000: CTRL (Device control register) 0x00F00249
Duplex: full
Endian mode (buffers): little
Link reset: reset
Set link up: 1
Invert Loss-Of-Signal: no
Receive flow control: disabled
Transmit flow control: disabled
VLAN mode: disabled
Auto speed detect: disabled
Speed select: 1000Mb/s
Force speed: no
Force duplex: no
0x00008: STATUS (Device status register) 0x0000C343
Duplex: full
Link up: link config
TBI mode: disabled
Link speed: 100Mb/s
Bus type: PCI
Bus speed: 33MHz
Bus width: 32-bit
0x00100: RCTL (Receive control register) 0x00008002
Receiver: enabled
Store bad packets: disabled
Unicast promiscuous: disabled
Multicast promiscuous: disabled
Long packet: disabled
Descriptor minimum threshold size: 1/2
Broadcast accept mode: accept
VLAN filter: disabled
Cononical form indicator: disabled
Discard pause frames: filtered
Pass MAC control frames: don't pass
Receive buffer size: 2048
0x02808: RDLEN (Receive desc length) 0x00001000
0x02810: RDH (Receive desc head) 0x00000003
0x02818: RDT (Receive desc tail) 0x00000000
0x02820: RDTR (Receive delay timer) 0x00000000
0x00400: TCTL (Transmit ctrl register) 0x000400FA
Transmitter: enabled
Pad short packets: enabled
Software XOFF Transmission: disabled
Re-transmit on late collision: disabled
0x03808: TDLEN (Transmit desc length) 0x00001000
0x03810: TDH (Transmit desc head) 0x000000D8
0x03818: TDT (Transmit desc tail) 0x000000D8
0x03820: TIDV (Transmit delay timer) 0x00000040
PHY type: M88
# uname -a
Linux victory 2.6.11-rc4-mm1 #4 Fri Feb 25 18:19:43 CST 2005 x86_64 AMD
Athlon(tm) 64 Processor 3200+ AuthenticAMD GNU/Linux
On Wednesday 09 March 2005 05:09 pm, Ben Greear wrote:
> Ganesh Venkatesan wrote:
> > Ben:
> >
> > Are you using the e1000 that is included in the 2.6.11 kernel? ethtool
> > -d eth? works fine for me. What else is different in your env?
>
> I have patched the e1000 in my 2.6.11 kernel, but I see this -d problem
> on other un-patched systems as well, so it can't be (just) my patches
> that are the problem.
>
> I also tried this on my x86-64 opteron system, running FC3. I
> have not hacked up this kernel or user-space tools at all :)
>
> [root@grok lanforge]# ethtool -i eth3
> driver: e1000
> version: 5.5.4-k2-NAPI
> firmware-version: N/A
> bus-info: 0000:02:08.0
> [root@grok lanforge]# ethtool -d eth3
> Cannot dump registers: Success
> [root@grok lanforge]# uname -a
> Linux grok 2.6.10-1.766_FC3smp #1 SMP Wed Feb 9 23:17:48 EST 2005 x86_64
> x86_64 x86_64 GNU/Linux
>
>
> I'm using ethtool 1.8 on this system.
>
>
> What version of ethtool are you using?
--
Jon Mason
jdmason@xxxxxxxxxx
|