The patch adds ethtool get_ and set_settings support to the forcedeth nic
driver. This allows to force a certain link speed with ethtool -s.
Supported link speeds: 10 HD&FD, 100 HD&FD, 1000 FD
1000 HD is not supported (probably a hardware restriction), 1000 FD is
only supported with autonegotiation enabled.
Changelog:
- Code reorganization: move ethtool functions further down in forcedeth.c
(no code changes within the existing ethtool functions)
- add support for setting the link setting bits in the nic with
autodetection in the PHY disabled (i.e. use a netdev_priv() variable
instead of querying the PHY)
- implement get_settings and set_settings ethtool functions.
Signed-Off-By: Manfred Spraul <manfred@xxxxxxxxxxxxxxxx>
// Kernel Version:
// VERSION = 2
// PATCHLEVEL = 6
// SUBLEVEL = 10
// EXTRAVERSION =-rc1
--- 2.6/drivers/net/forcedeth.c 2004-11-14 14:50:21.000000000 +0100
+++ build-2.6/drivers/net/forcedeth.c 2004-11-17 05:55:13.440930446 +0100
@@ -79,6 +79,8 @@
* 0.30: 25 Sep 2004: rx checksum support for nf 250 Gb. Add rx reset
* into nv_close, otherwise reenabling for wol can
* cause DMA to kfree'd memory.
+ * 0.31: 14 Nov 2004: ethtool support for getting/setting link
+ * capabilities.
*
* Known bugs:
* We suspect that on some hardware no TX done interrupts are generated.
@@ -90,7 +92,7 @@
* DEV_NEED_TIMERIRQ will not harm you on sane hardware, only generating a few
* superfluous timer interrupts from the nic.
*/
-#define FORCEDETH_VERSION "0.30"
+#define FORCEDETH_VERSION "0.31"
#define DRV_NAME "forcedeth"
#include <linux/module.h>
@@ -210,6 +212,7 @@ enum {
#define NVREG_LINKSPEED_10 1000
#define NVREG_LINKSPEED_100 100
#define NVREG_LINKSPEED_1000 50
+#define NVREG_LINKSPEED_MASK (0xFFF)
NvRegUnknownSetupReg5 = 0x130,
#define NVREG_UNKSETUP5_BIT31 (1<<31)
NvRegUnknownSetupReg3 = 0x13c,
@@ -441,6 +444,8 @@ struct fe_priv {
int in_shutdown;
u32 linkspeed;
int duplex;
+ int autoneg;
+ int fixed_mode;
int phyaddr;
int wolenabled;
unsigned int phy_oui;
@@ -765,50 +770,6 @@ static struct net_device_stats *nv_get_s
return &np->stats;
}
-static void nv_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo
*info)
-{
- struct fe_priv *np = get_nvpriv(dev);
- strcpy(info->driver, "forcedeth");
- strcpy(info->version, FORCEDETH_VERSION);
- strcpy(info->bus_info, pci_name(np->pci_dev));
-}
-
-static void nv_get_wol(struct net_device *dev, struct ethtool_wolinfo *wolinfo)
-{
- struct fe_priv *np = get_nvpriv(dev);
- wolinfo->supported = WAKE_MAGIC;
-
- spin_lock_irq(&np->lock);
- if (np->wolenabled)
- wolinfo->wolopts = WAKE_MAGIC;
- spin_unlock_irq(&np->lock);
-}
-
-static int nv_set_wol(struct net_device *dev, struct ethtool_wolinfo *wolinfo)
-{
- struct fe_priv *np = get_nvpriv(dev);
- u8 __iomem *base = get_hwbase(dev);
-
- spin_lock_irq(&np->lock);
- if (wolinfo->wolopts == 0) {
- writel(0, base + NvRegWakeUpFlags);
- np->wolenabled = 0;
- }
- if (wolinfo->wolopts & WAKE_MAGIC) {
- writel(NVREG_WAKEUPFLAGS_ENABLE, base + NvRegWakeUpFlags);
- np->wolenabled = 1;
- }
- spin_unlock_irq(&np->lock);
- return 0;
-}
-
-static struct ethtool_ops ops = {
- .get_drvinfo = nv_get_drvinfo,
- .get_link = ethtool_op_get_link,
- .get_wol = nv_get_wol,
- .set_wol = nv_set_wol,
-};
-
/*
* nv_alloc_rx: fill rx ring entries.
* Return 1 if the allocations for the skbs failed and the
@@ -1286,6 +1247,25 @@ static int nv_update_linkspeed(struct ne
goto set_speed;
}
+ if (np->autoneg == 0) {
+ dprintk(KERN_DEBUG "%s: nv_update_linkspeed: autoneg off, PHY
set to 0x%04x.\n",
+ dev->name, np->fixed_mode);
+ if (np->fixed_mode & LPA_100FULL) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_100;
+ newdup = 1;
+ } else if (np->fixed_mode & LPA_100HALF) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_100;
+ newdup = 0;
+ } else if (np->fixed_mode & LPA_10FULL) {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ newdup = 1;
+ } else {
+ newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ newdup = 0;
+ }
+ retval = 1;
+ goto set_speed;
+ }
/* check auto negotiation is complete */
if (!(mii_status & BMSR_ANEGCOMPLETE)) {
/* still in autonegotiation - configure nic for 10 MBit HD and
wait. */
@@ -1303,7 +1283,7 @@ static int nv_update_linkspeed(struct ne
if ((control_1000 & ADVERTISE_1000FULL) &&
(status_1000 & LPA_1000FULL)) {
- dprintk(KERN_DEBUG "%s: nv_update_linkspeed: GBit ethernet
detected.\n",
+ dprintk(KERN_DEBUG "%s: nv_update_linkspeed: GBit
ethernet detected.\n",
dev->name);
newls = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_1000;
newdup = 1;
@@ -1362,9 +1342,9 @@ set_speed:
phyreg &= ~(PHY_HALF|PHY_100|PHY_1000);
if (np->duplex == 0)
phyreg |= PHY_HALF;
- if ((np->linkspeed & 0xFFF) == NVREG_LINKSPEED_100)
+ if ((np->linkspeed & NVREG_LINKSPEED_MASK) == NVREG_LINKSPEED_100)
phyreg |= PHY_100;
- else if ((np->linkspeed & 0xFFF) == NVREG_LINKSPEED_1000)
+ else if ((np->linkspeed & NVREG_LINKSPEED_MASK) == NVREG_LINKSPEED_1000)
phyreg |= PHY_1000;
writel(phyreg, base + NvRegPhyInterface);
@@ -1500,6 +1480,227 @@ static void nv_do_nic_poll(unsigned long
enable_irq(dev->irq);
}
+static void nv_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo
*info)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ strcpy(info->driver, "forcedeth");
+ strcpy(info->version, FORCEDETH_VERSION);
+ strcpy(info->bus_info, pci_name(np->pci_dev));
+}
+
+static void nv_get_wol(struct net_device *dev, struct ethtool_wolinfo *wolinfo)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ wolinfo->supported = WAKE_MAGIC;
+
+ spin_lock_irq(&np->lock);
+ if (np->wolenabled)
+ wolinfo->wolopts = WAKE_MAGIC;
+ spin_unlock_irq(&np->lock);
+}
+
+static int nv_set_wol(struct net_device *dev, struct ethtool_wolinfo *wolinfo)
+{
+ struct fe_priv *np = get_nvpriv(dev);
+ u8 __iomem *base = get_hwbase(dev);
+
+ spin_lock_irq(&np->lock);
+ if (wolinfo->wolopts == 0) {
+ writel(0, base + NvRegWakeUpFlags);
+ np->wolenabled = 0;
+ }
+ if (wolinfo->wolopts & WAKE_MAGIC) {
+ writel(NVREG_WAKEUPFLAGS_ENABLE, base + NvRegWakeUpFlags);
+ np->wolenabled = 1;
+ }
+ spin_unlock_irq(&np->lock);
+ return 0;
+}
+
+static int nv_get_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct fe_priv *np = netdev_priv(dev);
+ int adv;
+
+ spin_lock_irq(&np->lock);
+ ecmd->port = PORT_MII;
+ if (!netif_running(dev)) {
+ /* We do not track link speed / duplex setting if the
+ * interface is disabled. Force a link check */
+ nv_update_linkspeed(dev);
+ }
+ switch(np->linkspeed & (NVREG_LINKSPEED_MASK)) {
+ case NVREG_LINKSPEED_10:
+ ecmd->speed = SPEED_10;
+ break;
+ case NVREG_LINKSPEED_100:
+ ecmd->speed = SPEED_100;
+ break;
+ case NVREG_LINKSPEED_1000:
+ ecmd->speed = SPEED_1000;
+ break;
+ }
+ ecmd->duplex = DUPLEX_HALF;
+ if (np->duplex)
+ ecmd->duplex = DUPLEX_FULL;
+
+ ecmd->autoneg = np->autoneg;
+
+ ecmd->advertising = ADVERTISED_MII;
+ if (np->autoneg) {
+ ecmd->advertising |= ADVERTISED_Autoneg;
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ } else {
+ adv = np->fixed_mode;
+ }
+ if (adv & ADVERTISE_10HALF)
+ ecmd->advertising |= ADVERTISED_10baseT_Half;
+ if (adv & ADVERTISE_10FULL)
+ ecmd->advertising |= ADVERTISED_10baseT_Full;
+ if (adv & ADVERTISE_100HALF)
+ ecmd->advertising |= ADVERTISED_100baseT_Half;
+ if (adv & ADVERTISE_100FULL)
+ ecmd->advertising |= ADVERTISED_100baseT_Full;
+ if (np->autoneg && np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ if (adv & ADVERTISE_1000FULL)
+ ecmd->advertising |= ADVERTISED_1000baseT_Full;
+ }
+
+ ecmd->supported = (SUPPORTED_Autoneg |
+ SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full |
+ SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full |
+ SUPPORTED_MII);
+ if (np->gigabit == PHY_GIGABIT)
+ ecmd->supported |= SUPPORTED_1000baseT_Full;
+
+ ecmd->phy_address = np->phyaddr;
+ ecmd->transceiver = XCVR_EXTERNAL;
+
+ /* ignore maxtxpkt, maxrxpkt for now */
+ spin_unlock_irq(&np->lock);
+ return 0;
+}
+
+static int nv_set_settings(struct net_device *dev, struct ethtool_cmd *ecmd)
+{
+ struct fe_priv *np = netdev_priv(dev);
+
+ if (ecmd->port != PORT_MII)
+ return -EINVAL;
+ if (ecmd->transceiver != XCVR_EXTERNAL)
+ return -EINVAL;
+ if (ecmd->phy_address != np->phyaddr) {
+ /* TODO: support switching between multiple phys. Should be
+ * trivial, but not enabled due to lack of test hardware. */
+ return -EINVAL;
+ }
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ u32 mask;
+
+ mask = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full |
+ ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full;
+ if (np->gigabit == PHY_GIGABIT)
+ mask |= ADVERTISED_1000baseT_Full;
+
+ if ((ecmd->advertising & mask) == 0)
+ return -EINVAL;
+
+ } else if (ecmd->autoneg == AUTONEG_DISABLE) {
+ /* Note: autonegotiation disable, speed 1000 intentionally
+ * forbidden - noone should need that. */
+
+ if (ecmd->speed != SPEED_10 && ecmd->speed != SPEED_100)
+ return -EINVAL;
+ if (ecmd->duplex != DUPLEX_HALF && ecmd->duplex != DUPLEX_FULL)
+ return -EINVAL;
+ } else {
+ return -EINVAL;
+ }
+
+ spin_lock_irq(&np->lock);
+ if (ecmd->autoneg == AUTONEG_ENABLE) {
+ int adv, bmcr;
+
+ np->autoneg = 1;
+
+ /* advertise only what has been requested */
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
+ if (ecmd->advertising & ADVERTISED_10baseT_Half)
+ adv |= ADVERTISE_10HALF;
+ if (ecmd->advertising & ADVERTISED_10baseT_Full)
+ adv |= ADVERTISE_10FULL;
+ if (ecmd->advertising & ADVERTISED_100baseT_Half)
+ adv |= ADVERTISE_100HALF;
+ if (ecmd->advertising & ADVERTISED_100baseT_Full)
+ adv |= ADVERTISE_100FULL;
+ mii_rw(dev, np->phyaddr, MII_ADVERTISE, adv);
+
+ if (np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ adv &= ~ADVERTISE_1000FULL;
+ if (ecmd->advertising & ADVERTISED_1000baseT_Full)
+ adv |= ADVERTISE_1000FULL;
+ mii_rw(dev, np->phyaddr, MII_1000BT_CR, adv);
+ }
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= (BMCR_ANENABLE | BMCR_ANRESTART);
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ } else {
+ int adv, bmcr;
+
+ np->autoneg = 0;
+
+ adv = mii_rw(dev, np->phyaddr, MII_ADVERTISE, MII_READ);
+ adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4);
+ if (ecmd->speed == SPEED_10 && ecmd->duplex == DUPLEX_HALF)
+ adv |= ADVERTISE_10HALF;
+ if (ecmd->speed == SPEED_10 && ecmd->duplex == DUPLEX_FULL)
+ adv |= ADVERTISE_10FULL;
+ if (ecmd->speed == SPEED_100 && ecmd->duplex == DUPLEX_HALF)
+ adv |= ADVERTISE_100HALF;
+ if (ecmd->speed == SPEED_100 && ecmd->duplex == DUPLEX_FULL)
+ adv |= ADVERTISE_100FULL;
+ mii_rw(dev, np->phyaddr, MII_ADVERTISE, adv);
+ np->fixed_mode = adv;
+
+ if (np->gigabit == PHY_GIGABIT) {
+ adv = mii_rw(dev, np->phyaddr, MII_1000BT_CR, MII_READ);
+ adv &= ~ADVERTISE_1000FULL;
+ mii_rw(dev, np->phyaddr, MII_1000BT_CR, adv);
+ }
+
+ bmcr = mii_rw(dev, np->phyaddr, MII_BMCR, MII_READ);
+ bmcr |= ~(BMCR_ANENABLE|BMCR_SPEED100|BMCR_FULLDPLX);
+ if (adv & (ADVERTISE_10FULL|ADVERTISE_100FULL))
+ bmcr |= BMCR_FULLDPLX;
+ if (adv & (ADVERTISE_100HALF|ADVERTISE_100FULL))
+ bmcr |= BMCR_SPEED100;
+ mii_rw(dev, np->phyaddr, MII_BMCR, bmcr);
+
+ if (netif_running(dev)) {
+ /* Wait a bit and then reconfigure the nic. */
+ udelay(10);
+ nv_linkchange(dev);
+ }
+ }
+ spin_unlock_irq(&np->lock);
+
+ return 0;
+}
+
+static struct ethtool_ops ops = {
+ .get_drvinfo = nv_get_drvinfo,
+ .get_link = ethtool_op_get_link,
+ .get_wol = nv_get_wol,
+ .set_wol = nv_set_wol,
+ .get_settings = nv_get_settings,
+ .set_settings = nv_set_settings,
+};
+
static int nv_open(struct net_device *dev)
{
struct fe_priv *np = get_nvpriv(dev);
@@ -1550,9 +1751,6 @@ static int nv_open(struct net_device *de
base + NvRegRingSizes);
/* 5) continue setup */
- np->linkspeed = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
- np->duplex = 0;
-
writel(np->linkspeed, base + NvRegLinkSpeed);
writel(NVREG_UNKSETUP3_VAL1, base + NvRegUnknownSetupReg3);
writel(np->desc_ver, base + NvRegTxRxControl);
@@ -1866,6 +2064,11 @@ static int __devinit nv_probe(struct pci
phy_init(dev);
}
+ /* set default link speed settings */
+ np->linkspeed = NVREG_LINKSPEED_FORCE|NVREG_LINKSPEED_10;
+ np->duplex = 0;
+ np->autoneg = 1;
+
err = register_netdev(dev);
if (err) {
printk(KERN_INFO "forcedeth: unable to register netdev: %d\n",
err);
|