Thank you to Stan and Dave for helping me through this.
Ok, here's the file, printed below.
Basically, I'm running the following commands under Ubuntu 12.10:
Type mkdir /mnt/fp
Type mkdir /mnt/hr20
Type mount -t xfs -o rtdev=/dev/sda3 /dev/sda2 /mnt/fp
Type mount -t xfs -o rtdev=/dev/sdb3 /dev/sdb2 /mnt/hr20
Type xfsdump -J - /mnt/hr20 | xfsrestore -J - /mnt/fp
When run, I get this as my output:
xfsdump: WARNING: write to stdio failed: 32 (Broken pipe)
xfsdump: ending media file
xfsdump: media file size 18874368 bytes
xfsdump: dump size (non-dir files) : 13698056 bytes
xfsdump: NOTE: dump interrupted: 16 seconds elapsed
xfsdump: Dump Status: INTERRUPT
This happens each time. In the forum where this copy procedure was
suggested, they've been reporting that the latest xfsprogs is creating these
errors, which didn't happen under at least somewhat earlier versions.
The version of xfsprogs should be in the file, but it was just downloaded a
few days ago using git.
Best,
Jeffrey
xfs requested data file:
kernel version: Linux jeffrey 3.5.0-18-generic #29-Ubuntu SMP Fri Oct 19
10:27:31 UTC 2012 i686 i686 i686 GNU/Linux
xfsprogs version: xfs_repair version 3.1.8
number of CPU's: 8
contents of /proc/meminfo:
MemTotal: 6184324 kB
MemFree: 4986560 kB
Buffers: 32036 kB
Cached: 446368 kB
SwapCached: 0 kB
Active: 680296 kB
Inactive: 402548 kB
Active(anon): 612444 kB
Inactive(anon): 368 kB
Active(file): 67852 kB
Inactive(file): 402180 kB
Unevictable: 32596 kB
Mlocked: 32596 kB
HighTotal: 5365768 kB
HighFree: 4264648 kB
LowTotal: 818556 kB
LowFree: 721912 kB
SwapTotal: 1023996 kB
SwapFree: 1023996 kB
Dirty: 1484 kB
Writeback: 0 kB
AnonPages: 637224 kB
Mapped: 148540 kB
Shmem: 1284 kB
Slab: 36908 kB
SReclaimable: 16864 kB
SUnreclaim: 20044 kB
KernelStack: 3664 kB
PageTables: 8296 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 4116156 kB
Committed_AS: 3172256 kB
VmallocTotal: 122880 kB
VmallocUsed: 13156 kB
VmallocChunk: 104244 kB
HardwareCorrupted: 0 kB
AnonHugePages: 0 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
HugePages_Surp: 0
Hugepagesize: 2048 kB
DirectMap4k: 8184 kB
DirectMap2M: 905216 kB
contents of /proc/mounts:
rootfs / rootfs rw 0 0
sysfs /sys sysfs rw,nosuid,nodev,noexec,relatime 0 0
proc /proc proc rw,nosuid,nodev,noexec,relatime 0 0
udev /dev devtmpfs rw,relatime,size=3084428k,nr_inodes=200772,mode=755 0 0
devpts /dev/pts devpts rw,nosuid,noexec,relatime,gid=5,mode=620,ptmxmode=000
0 0
tmpfs /run tmpfs rw,nosuid,relatime,size=1236868k,mode=755 0 0
/dev/disk/by-uuid/e33b147d-faaa-4e55-8f3b-2fb2d3168053 / ext4
rw,relatime,errors=remount-ro,data=ordered 0 0
none /sys/fs/fuse/connections fusectl rw,relatime 0 0
none /sys/kernel/debug debugfs rw,relatime 0 0
none /sys/kernel/security securityfs rw,relatime 0 0
none /run/lock tmpfs rw,nosuid,nodev,noexec,relatime,size=5120k 0 0
none /run/shm tmpfs rw,nosuid,nodev,relatime 0 0
none /run/user tmpfs rw,nosuid,nodev,noexec,relatime,size=102400k,mode=755 0
0
gvfsd-fuse /run/user/jeffrey/gvfs fuse.gvfsd-fuse
rw,nosuid,nodev,relatime,user_id=1000,group_id=1000 0 0
contents of /proc/partitions:
major minor #blocks name
11 0 1048575 sr0
8 0 1953514584 sda
8 1 530113 sda1
8 2 15735664 sda2
8 3 1937246216 sda3
8 16 488386584 sdb
8 17 530113 sdb1
8 18 15735664 sdb2
8 19 472118216 sdb3
8 32 1953514584 sdc
8 33 1024000 sdc1
8 34 1952489258 sdc2
11 1 1048575 sr1
RAID Layout: no Raid
LVM Configuration: Sorry, I didn't have the education to get this
information.
Type of discs: 2 3.5² SATA drives, 1 half-height SATA.
hdparm results:
/dev/sda:
ATA device, with non-removable media
Model Number: Hitachi HDS723020BLA642
Serial Number: MN1240FA04NWHD
Firmware Revision: MN6OA800
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions,
SATA Rev 2.5, SATA Rev 2.6; Revision: ATA8-AST T13 Project D1697 Revision 0b
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 3907029168
Logical Sector size: 512 bytes
Physical Sector size: 512 bytes
device size with M = 1024*1024: 1907729 MBytes
device size with M = 1000*1000: 2000398 MBytes (2000 GB)
cache/buffer size = unknown
Form Factor: 3.5 inch
Nominal Media Rotation Rate: 7200
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: disabled
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
* SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
unknown 119[7]
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* NCQ priority information
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
420min for SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000cca36ac21fe4
NAA : 5
IEEE OUI : 000cca
Unique ID : 36ac21fe4
Checksum: correct
/dev/sdb:
ATA device, with non-removable media
Model Number: ST3500312CS
Serial Number: 6VV60HXR
Firmware Revision: SC13
Transport: Serial
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 976773168
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 476940 MBytes
device size with M = 1000*1000: 500107 MBytes (500 GB)
cache/buffer size = 8192 KBytes
Nominal Media Rotation Rate: 5900
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = ?
Advanced power management level: 254
Recommended acoustic management value: 254, current value: 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
* Advanced Power Management feature set
Power-Up In Standby feature set
SET_FEATURES required to spinup after power up
* SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* Media Card Pass-Through
* General Purpose Logging feature set
* 64-bit World wide name
Write-Read-Verify feature set
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Native Command Queueing (NCQ)
* Phy event counters
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
supported: enhanced erase
100min for SECURITY ERASE UNIT. 100min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000c500307c5d66
NAA : 5
IEEE OUI : 000c50
Unique ID : 0307c5d66
Checksum: correct
/dev/sdc:
ATA device, with non-removable media
Model Number: Hitachi HDS723020BLA642
Serial Number: MN3220F32KR53E
Firmware Revision: MN6OA800
Transport: Serial, ATA8-AST, SATA 1.0a, SATA II Extensions,
SATA Rev 2.5, SATA Rev 2.6; Revision: ATA8-AST T13 Project D1697 Revision 0b
Standards:
Used: unknown (minor revision code 0x0029)
Supported: 8 7 6 5
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 3907029168
Logical Sector size: 512 bytes
Physical Sector size: 512 bytes
device size with M = 1024*1024: 1907729 MBytes
device size with M = 1000*1000: 2000398 MBytes (2000 GB)
cache/buffer size = unknown
Form Factor: 3.5 inch
Nominal Media Rotation Rate: 7200
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
Advanced power management level: disabled
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Advanced Power Management feature set
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
* SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* WRITE_{DMA|MULTIPLE}_FUA_EXT
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
unknown 119[7]
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* NCQ priority information
Non-Zero buffer offsets in DMA Setup FIS
DMA Setup Auto-Activate optimization
Device-initiated interface power management
In-order data delivery
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
456min for SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 5000cca369e43c85
NAA : 5
IEEE OUI : 000cca
Unique ID : 369e43c85
Checksum: correct
Size of BBWC and Mode: Again, sorry, I couldn't find how to get this.
xfs_info:
root@jeffrey:~# xfs_info /mnt/fp
meta-data=/dev/sda2 isize=256 agcount=16, agsize=245869 blks
= sectsz=512 attr=0
data = bsize=4096 blocks=3933904, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=2560, version=1
= sectsz=512 sunit=0 blks, lazy-count=0
realtime =external extsz=1048576 blocks=484311554,
rtextents=1891842
root@jeffrey:~# xfs_info /mnt/hr20
meta-data=/dev/sdb2 isize=256 agcount=16, agsize=245869 blks
= sectsz=512 attr=0
data = bsize=4096 blocks=3933904, imaxpct=25
= sunit=0 swidth=0 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=2560, version=1
= sectsz=512 sunit=0 blks, lazy-count=0
realtime =external extsz=1048576 blocks=118029554,
rtextents=461052
|