hi!
thanks for all your answers
parted:
Disk geometry for /dev/sda: 0.000-3147012,000 megabytes
Disk label type: msdos
Minor Start End Type Filesystem Flags
1 0,031 1049854,423 primary xfs
cat /proc/partitions
8 0 3222540288 sda
8 1 1075050898 sda1
tw_cli (3ware raid tool)
Unit UnitType Status %Cmpl Stripe Size(GB) Cache AVerify IgnECC
------------------------------------------------------------------------------
u0 RAID-5 OK - 64K 3073.25 ON OFF OFF
Port Status Unit Size Blocks Serial
---------------------------------------------------------------
p0 OK u0 279.46 GB 586072368 3NF04F4D
p1 OK u0 279.46 GB 586072368 3NF09YMR
p2 OK u0 279.46 GB 586072368 3NF0AGN2
p3 OK u0 279.46 GB 586072368 3NF0D6ZM
p4 OK u0 279.46 GB 586072368 3NF0BG47
p5 OK u0 279.46 GB 586072368 3NF09YQT
p6 OK u0 279.46 GB 586072368 3NF02SMD
p7 OK u0 279.46 GB 586072368 3NF01YL5
p8 OK u0 279.46 GB 586072368 3NF02J46
p9 OK u0 279.46 GB 586072368 3NF04EYE
p10 OK u0 279.46 GB 586072368 3NF0ECRG
p11 OK u0 279.46 GB 586072368 3NF071X5
Name OnlineState BBUReady Status Volt Temp Hours LastCapTest
---------------------------------------------------------------------------
bbu On Yes OK OK OK 255 23-Aug-2005
dmesg:
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
ACPI: PCI interrupt 0000:04:02.0[A] -> GSI 52 (level, low) -> IRQ 185
scsi_proc_hostdir_add: proc_mkdir failed for <NULL>
3w-9xxx: scsi0: AEN: INFO (0x04:0x0055): <NULL>:.
3w-9xxx: scsi0: AEN: INFO (0x04:0x0053): <NULL>:.
scsi0 : 3ware 9000 Storage Controller
3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xfeaf0000, IRQ: 185.
3w-9xxx: scsi0: Firmware FE9X 2.06.00.009, BIOS BE9X 2.03.01.051, Ports: 12.
Vendor: AMCC Model: 9500S-12 DISK Rev: 2.06
Type: Direct-Access ANSI SCSI revision: 03
sda : very big device. try to use READ CAPACITY(16).
SCSI device sda: 6445080576 512-byte hdwr sectors (3299881 MB)
SCSI device sda: drive cache: write back, no read (daft)
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
what is a usv? sorry a german shurtcut. i mean ups.
no i have nothing changed on the system. normal shutdown for changing the ups
and then boot. and know i can not mount the drive ....
yes it is the same kernel (debian 2.6.8-2-686-smp)
i have know updated xfsprogs to 2.8.11 and i get a new error message with
xfs_check:
xfs_check /dev/sda1
XFS: Log inconsistent (didn't find previous header)
XFS: failed to find log head
ERROR: cannot find log head/tail, run xfs_repair
i will try ... and hope
with friendly greetings,
christian gattermair
|