I read from some e-mail sent in March that you planned to have new kernel
available for
the SGI540.
I also read that other people have keyboard problems.
I have installed Mandrake 6.1-1 on my SGI 540.
In single CPU it works fine.
With a multiCPU kernel (based on your information on http://www.linux.sgi.com)
I am not
able to use the keybord .. via telnet everything is fine!
In attach you will find the log file I get at boot time ..
probably it could help.
regards
Gabriele c version pgcc-2.91.66 19990314 (egcs-1.1.2 release)) #2 SMP Thu Apr 27
08:17:14 EDT 2000
Silicon Graphics 540 (rev 2)
VISWS HACK: hard-wiring physical mem size to 128Mb
VISWS HACK: taking 16Mb for gfx memory -- leaving 240Mb for kernel
sgivw_gfx_mem_phys f000000
Processor #0 Pentium(tm) Pro APIC version 17
Processor #1 Pentium(tm) Pro APIC version 17
Processor #2 Pentium(tm) Pro APIC version 17
Processor #3 Pentium(tm) Pro APIC version 17
mapped APIC to ffffe000 (fee00000)
Lithium PCI Bridge A, Bus Number: 1
Lithium PCI Bridge B (PIIX4), Bus Number: 0
Local APIC ID 0
Local APIC Version 40011
Cobalt Revision a5
Cobalt APIC ID 44000000
Cobalt APIC enabled: ID reg 44000100
WARNING: ASSIGN_IRQ_VECTOR wrapped back to 52
WARNING: ASSIGN_IRQ_VECTOR wrapped back to 53
IRQ 28, Cobalt APIC Entry 12, IDT Vector 82: enabling
Detected 551290253 Hz processor.
Starting Cobalt Timer system clock
IRQ 0, Cobalt APIC Entry 28, IDT Vector 51: enabling
Console: colour dummy device 80x25
Calibrating delay loop... 548.86 BogoMIPS
Memory: 241472k/245760k available (1064k kernel code, 416k reserved, 2736k
data, 72k init)
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... disabled
POSIX conformance testing by UNIFIX
per-CPU timeslice cutoff: 100.05 usecs.
CPU0: Intel 00/07 stepping 03
calibrating APIC timer ...
..... CPU clock speed is 551.2423 MHz.
..... system bus clock speed is 100.2256 MHz.
Booting processor 1 eip 2000
Calibrating delay loop... 548.86 BogoMIPS
OK.
CPU1: Intel 00/07 stepping 03
Booting processor 2 eip 2000
Calibrating delay loop... 548.86 BogoMIPS
OK.
CPU2: Intel 00/07 stepping 03
Booting processor 3 eip 2000
Calibrating delay loop... 548.86 BogoMIPS
OK.
CPU3: Intel 00/07 stepping 03
Total of 4 processors activated (2195.46 BogoMIPS).
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI->APIC IRQ transform: (B0,I4,P3) -> 23
PCI->APIC IRQ transform: (B1,I2,P0) -> 18
PCI->APIC IRQ transform: (B1,I3,P0) -> 19
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
IRQ 23, Cobalt APIC Entry 7, IDT Vector 5a: enabling
USB HID boot protocol mouse registered.
sgivwfb: framebuffer at 0xf000000, size 16384k
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: i2c wait-state timeout.
sgivwfb: Unknown flatpanel type 0 detected.
sgivwfb: new video mode xres=800 yres=600 bpp=8
vxres=800 vyres=600
Console: switching to colour frame buffer device 100x37
fb0: Virtual frame buffer device, using 16384K of video memory
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
pty: 256 Unix98 ptys configured
probe_vwsnd: lithium audio found
usb_hub_thread at c01d4720
keyboard: Too many NACKs -- noisy kbd cable?
keyboard: Too many NACKs -- noisy kbd cable?
uhci_control_thread at c01d2b14
IRQ 38, Cobalt APIC Entry 22, IDT Vector d2: enabling
PIIX4: IDE controller on PCI bus 00 dev 21
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x2020-0x2027, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x2028-0x202f, BIOS settings: hdc:pio, hdd:pio
hda: IRQ probe failed (0)
hda: IRQ probe failed (0)
hda: CD-532E-A, ATAPI CDROM drive
hda: IRQ probe failed (0)
hdb: IRQ probe failed (0)
hdb: IRQ probe failed (0)
hdb: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
hdb: IRQ probe failed (0)
IRQ 14, Cobalt APIC Entry 4, IDT Vector c1: enabling
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.55
VISWS HACK: floppy drive 0 hardwired to 1.44Mb (cmos WAR)
VISWS HACK: floppy drive 1 hardwired to (none) (cmos WAR)
Floppy drive(s): fd0 is 1.44M, fd1 is unknown type 16 (usb?)
FDC 0 is a National Semiconductor PC87306
(scsi): Found a QLA1080 @ bus 1, device 2, irq 18, iobase 0xa000
(scsi): Initializing Adapter; Please wait ...
scsi(0): Determining if RISC is loaded...
scsi(0): Verifying chip...
scsi(0): Configure NVRAM parameters...
scsi(0): Resetting SCSI BUS (0)
IRQ 18, Cobalt APIC Entry 2, IDT Vector e1: enabling
scsi0 : QLogic QLA1080 PCI to SCSI Host Adapter: bus 1 device 2 irq 18
Version: 1.20-Beta, Firmware version: 8.9.0
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
scsi : 2 hosts.
Unable to handle kernel paging request at virtual address f000c218
current->tss.cr3 = 00101000, %cr3 = 00101000
*pde = 00000000
Oops: 0002
CPU: 0
EIP: 0010:[<c01d2110>]
EFLAGS: 00010202
eax: f000c1f0 ebx: c04d6000 ecx: c04fe188 edx: 00000061
esi: c04fe008 edi: c04d7e78 ebp: c04fe108 esp: c04d7e6c
ds: 0018 es: 0018 ss: 0018
Process uhci-control (pid: 5, process nr: 8, stackpage=c04d7000)
Stack: c04fe108 c04fe148 c04d7e78 c04d6000 c025b0fc c01d234e c04fe000 c04fe108
c04fe188 c0011c00 00000008 c0011c14 c0011c14 c04d7edc 3c800000 c04fe108
c04fe000 c01d3a58 c0011c00 00000000 c04d7ed4 c0011c1c 00000000 00000000
Call Trace: [<c01d234e>] [<c01d3a58>] [<c01d4009>] [<c01d2669>] [<c01d269c>]
[<c01d2bc4>] [<c0107a66>]
[<c01d2b14>] [<c010651a>] [<c0106523>]
Code: 89 70 28 f6 00 01 74 dc 8b 4c 24 28 51 55 56 e8 e4 fb ff ff
Vendor: SEAGATE Model: ST118202LC Rev: 0006
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
scsi(0:0:0:0): Enabled tagged queuing, queue depth 255.
Vendor: IOMEGA Model: ZIP 100 Rev: 12.A
Type: Direct-Access ANSI SCSI revision: 00
Detected scsi removable disk sdb at scsi1, channel 0, id 0, lun 0
scsi : detected 2 SCSI disks total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 35566480 [17366 MB] [17.4 GB]
sdb : READ CAPACITY failed.
sdb : status = 0, message = 00, host = 0, driver = 28
sdb : extended sense code = 2
sdb : block size assumed to be 512 bytes, disk size 1GB.
eth0: Intel EtherExpress Pro 10/100 at 0xa100, 08:00:69:12:E6:01, IRQ 19.
Board assembly 123456-120, Physical connectors present: RJ45
Primary interface chip DP83840 PHY #1.
DP83840 specific setup, setting register 23 to 0422.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
Receiver lock-up workaround activated.
Partition check:
sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
sdb:scsidisk I/O error: dev 08:10, sector 0
unable to read partition table
hdb:<3>ide-scsi: hdb: unsupported command in request queue (0)
end_request: I/O error, dev 03:40 (hdb), sector 0
unable to read partition table
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Adding Swap: 136516k swap-space (priority -1)
Adding Swap: 136516k swap-space (priority -2)
Adding Swap: 136516k swap-space (priority -3)
Adding Swap: 136516k swap-space (priority -4)
|