Return to sa1100_neponset.c CVS log

Up to [Development] / linux-2.6-xfs / drivers / pcmcia

Initial Import 2.6.0

/*
 * linux/drivers/pcmcia/sa1100_neponset.c
 *
 * Neponset PCMCIA specific routines
 */
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched.h>
#include <linux/device.h>
#include <linux/errno.h>
#include <linux/init.h>

#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/arch/neponset.h>
#include <asm/hardware/sa1111.h>

#include "sa1111_generic.h"

/*
 * Neponset uses the Maxim MAX1600, with the following connections:
 *
 *   MAX1600      Neponset
 *
 *    A0VCC        SA-1111 GPIO A<1>
 *    A1VCC        SA-1111 GPIO A<0>
 *    A0VPP        CPLD NCR A0VPP
 *    A1VPP        CPLD NCR A1VPP
 *    B0VCC        SA-1111 GPIO A<2>
 *    B1VCC        SA-1111 GPIO A<3>
 *    B0VPP        ground (slot B is CF)
 *    B1VPP        ground (slot B is CF)
 *
 *     VX          VCC (5V)
 *     VY          VCC3_3 (3.3V)
 *     12INA       12V
 *     12INB       ground (slot B is CF)
 *
 * The MAX1600 CODE pin is tied to ground, placing the device in 
 * "Standard Intel code" mode. Refer to the Maxim data sheet for
 * the corresponding truth table.
 */

static int
neponset_pcmcia_configure_socket(struct sa1100_pcmcia_socket *skt, const socket_state_t *state)
{
	unsigned int ncr_mask, ncr_set, pa_dwr_mask, pa_dwr_set;
	int ret;

	switch (skt->nr) {
	case 0:
		pa_dwr_mask = GPIO_GPIO0 | GPIO_GPIO1;
		ncr_mask = NCR_A0VPP | NCR_A1VPP;

		if (state->Vpp == 0)
			ncr_set = 0;
		else if (state->Vpp == 120)
			ncr_set = NCR_A1VPP;
		else if (state->Vpp == state->Vcc)
			ncr_set = NCR_A0VPP;
		else {
			printk(KERN_ERR "%s(): unrecognized VPP %u\n",
			       __FUNCTION__, state->Vpp);
			return -1;
		}
		break;

	case 1:
		pa_dwr_mask = GPIO_GPIO2 | GPIO_GPIO3;
		ncr_mask = 0;
		ncr_set = 0;

		if (state->Vpp != state->Vcc && state->Vpp != 0) {
			printk(KERN_ERR "%s(): CF slot cannot support VPP %u\n",
			       __FUNCTION__, state->Vpp);
			return -1;
		}
		break;

	default:
		return -1;
	}

	/*
	 * pa_dwr_set is the mask for selecting Vcc on both sockets.
	 * pa_dwr_mask selects which bits (and therefore socket) we change.
	 */
	switch (state->Vcc) {
	default:
	case 0:  pa_dwr_set = 0;			break;
	case 33: pa_dwr_set = GPIO_GPIO1|GPIO_GPIO2;	break;
	case 50: pa_dwr_set = GPIO_GPIO0|GPIO_GPIO3;	break;
	}

	ret = sa1111_pcmcia_configure_socket(skt, state);
	if (ret == 0) {
		unsigned long flags;

		local_irq_save(flags);
		NCR_0 = (NCR_0 & ~ncr_mask) | ncr_set;

		PA_DWR = (PA_DWR & ~pa_dwr_mask) | (pa_dwr_set & pa_dwr_mask);
		local_irq_restore(flags);
	}

	return 0;
}

static void neponset_pcmcia_socket_init(struct sa1100_pcmcia_socket *skt)
{
	if (skt->nr == 0)
		NCR_0 &= ~(NCR_A0VPP | NCR_A1VPP);

        sa1111_pcmcia_socket_init(skt);
}

static struct pcmcia_low_level neponset_pcmcia_ops = {
        .owner                  = THIS_MODULE,
        .hw_init                = sa1111_pcmcia_hw_init,
        .hw_shutdown            = sa1111_pcmcia_hw_shutdown,
        .socket_state           = sa1111_pcmcia_socket_state,
        .configure_socket       = neponset_pcmcia_configure_socket,
        .socket_init            = neponset_pcmcia_socket_init,
        .socket_suspend         = sa1111_pcmcia_socket_suspend,
};

int __init pcmcia_neponset_init(struct device *dev)
{
        int ret = -ENODEV;

        if (machine_is_assabet()) {
                /*
                 * Set GPIO_A<3:0> to be outputs for the MAX1600,
                 * and switch to standby mode.
                 */
                PA_DDR = 0;
                PA_DWR = 0;
		PA_SDR = 0;
		PA_SSR = 0;
		ret = sa11xx_drv_pcmcia_probe(dev, &neponset_pcmcia_ops, 0, 2);
	}

	return ret;
}