/******************************************************************************
*
* Name: hwsleep.c - ACPI Hardware Sleep/Wake Interface
*
*****************************************************************************/
/*
* Copyright (C) 2000 - 2003, R. Byron Moore
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
* are met:
* 1. Redistributions of source code must retain the above copyright
* notice, this list of conditions, and the following disclaimer,
* without modification.
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
* substantially similar to the "NO WARRANTY" disclaimer below
* ("Disclaimer") and any redistribution must be conditioned upon
* including a substantially similar Disclaimer requirement for further
* binary redistribution.
* 3. Neither the names of the above-listed copyright holders nor the names
* of any contributors may be used to endorse or promote products derived
* from this software without specific prior written permission.
*
* Alternatively, this software may be distributed under the terms of the
* GNU General Public License ("GPL") version 2 as published by the Free
* Software Foundation.
*
* NO WARRANTY
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
* POSSIBILITY OF SUCH DAMAGES.
*/
#include <acpi/acpi.h>
#define _COMPONENT ACPI_HARDWARE
ACPI_MODULE_NAME ("hwsleep")
/******************************************************************************
*
* FUNCTION: acpi_set_firmware_waking_vector
*
* PARAMETERS: physical_address - Physical address of ACPI real mode
* entry point.
*
* RETURN: Status
*
* DESCRIPTION: access function for d_firmware_waking_vector field in FACS
*
******************************************************************************/
acpi_status
acpi_set_firmware_waking_vector (
acpi_physical_address physical_address)
{
ACPI_FUNCTION_TRACE ("acpi_set_firmware_waking_vector");
/* Set the vector */
if (acpi_gbl_common_fACS.vector_width == 32) {
*(ACPI_CAST_PTR (u32, acpi_gbl_common_fACS.firmware_waking_vector))
= (u32) physical_address;
}
else {
*acpi_gbl_common_fACS.firmware_waking_vector
= physical_address;
}
return_ACPI_STATUS (AE_OK);
}
/******************************************************************************
*
* FUNCTION: acpi_get_firmware_waking_vector
*
* PARAMETERS: *physical_address - Output buffer where contents of
* the firmware_waking_vector field of
* the FACS will be stored.
*
* RETURN: Status
*
* DESCRIPTION: Access function for firmware_waking_vector field in FACS
*
******************************************************************************/
acpi_status
acpi_get_firmware_waking_vector (
acpi_physical_address *physical_address)
{
ACPI_FUNCTION_TRACE ("acpi_get_firmware_waking_vector");
if (!physical_address) {
return_ACPI_STATUS (AE_BAD_PARAMETER);
}
/* Get the vector */
if (acpi_gbl_common_fACS.vector_width == 32) {
*physical_address = (acpi_physical_address)
*(ACPI_CAST_PTR (u32, acpi_gbl_common_fACS.firmware_waking_vector));
}
else {
*physical_address =
*acpi_gbl_common_fACS.firmware_waking_vector;
}
return_ACPI_STATUS (AE_OK);
}
/******************************************************************************
*
* FUNCTION: acpi_enter_sleep_state_prep
*
* PARAMETERS: sleep_state - Which sleep state to enter
*
* RETURN: Status
*
* DESCRIPTION: Prepare to enter a system sleep state (see ACPI 2.0 spec p 231)
* This function must execute with interrupts enabled.
* We break sleeping into 2 stages so that OSPM can handle
* various OS-specific tasks between the two steps.
*
******************************************************************************/
acpi_status
acpi_enter_sleep_state_prep (
u8 sleep_state)
{
acpi_status status;
struct acpi_object_list arg_list;
union acpi_object arg;
ACPI_FUNCTION_TRACE ("acpi_enter_sleep_state_prep");
/*
* _PSW methods could be run here to enable wake-on keyboard, LAN, etc.
*/
status = acpi_get_sleep_type_data (sleep_state,
&acpi_gbl_sleep_type_a, &acpi_gbl_sleep_type_b);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Setup parameter object */
arg_list.count = 1;
arg_list.pointer = &arg;
arg.type = ACPI_TYPE_INTEGER;
arg.integer.value = sleep_state;
/* Run the _PTS and _GTS methods */
status = acpi_evaluate_object (NULL, "\\_PTS", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
return_ACPI_STATUS (status);
}
status = acpi_evaluate_object (NULL, "\\_GTS", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
return_ACPI_STATUS (status);
}
/* Set the system indicators to show the desired sleep state. */
status = acpi_evaluate_object (NULL, "\\_SI._SST", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
ACPI_REPORT_ERROR (("Method _SST failed, %s\n", acpi_format_exception (status)));
}
return_ACPI_STATUS (AE_OK);
}
/******************************************************************************
*
* FUNCTION: acpi_enter_sleep_state
*
* PARAMETERS: sleep_state - Which sleep state to enter
*
* RETURN: Status
*
* DESCRIPTION: Enter a system sleep state (see ACPI 2.0 spec p 231)
* THIS FUNCTION MUST BE CALLED WITH INTERRUPTS DISABLED
*
******************************************************************************/
acpi_status
acpi_enter_sleep_state (
u8 sleep_state)
{
u32 PM1Acontrol;
u32 PM1Bcontrol;
struct acpi_bit_register_info *sleep_type_reg_info;
struct acpi_bit_register_info *sleep_enable_reg_info;
u32 in_value;
acpi_status status;
ACPI_FUNCTION_TRACE ("acpi_enter_sleep_state");
if ((acpi_gbl_sleep_type_a > ACPI_SLEEP_TYPE_MAX) ||
(acpi_gbl_sleep_type_b > ACPI_SLEEP_TYPE_MAX)) {
ACPI_REPORT_ERROR (("Sleep values out of range: A=%X B=%X\n",
acpi_gbl_sleep_type_a, acpi_gbl_sleep_type_b));
return_ACPI_STATUS (AE_AML_OPERAND_VALUE);
}
sleep_type_reg_info = acpi_hw_get_bit_register_info (ACPI_BITREG_SLEEP_TYPE_A);
sleep_enable_reg_info = acpi_hw_get_bit_register_info (ACPI_BITREG_SLEEP_ENABLE);
if (sleep_state != ACPI_STATE_S5) {
/* Clear wake status */
status = acpi_set_register (ACPI_BITREG_WAKE_STATUS, 1, ACPI_MTX_DO_NOT_LOCK);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
status = acpi_hw_clear_acpi_status (ACPI_MTX_DO_NOT_LOCK);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Disable BM arbitration */
status = acpi_set_register (ACPI_BITREG_ARB_DISABLE, 1, ACPI_MTX_DO_NOT_LOCK);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
}
status = acpi_hw_disable_non_wakeup_gpes();
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Get current value of PM1A control */
status = acpi_hw_register_read (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1_CONTROL, &PM1Acontrol);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
ACPI_DEBUG_PRINT ((ACPI_DB_INIT, "Entering sleep state [S%d]\n", sleep_state));
/* Clear SLP_EN and SLP_TYP fields */
PM1Acontrol &= ~(sleep_type_reg_info->access_bit_mask | sleep_enable_reg_info->access_bit_mask);
PM1Bcontrol = PM1Acontrol;
/* Insert SLP_TYP bits */
PM1Acontrol |= (acpi_gbl_sleep_type_a << sleep_type_reg_info->bit_position);
PM1Bcontrol |= (acpi_gbl_sleep_type_b << sleep_type_reg_info->bit_position);
/* Write #1: fill in SLP_TYP data */
status = acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1A_CONTROL, PM1Acontrol);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
status = acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1B_CONTROL, PM1Bcontrol);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Insert SLP_ENABLE bit */
PM1Acontrol |= sleep_enable_reg_info->access_bit_mask;
PM1Bcontrol |= sleep_enable_reg_info->access_bit_mask;
/* Write #2: SLP_TYP + SLP_EN */
ACPI_FLUSH_CPU_CACHE ();
status = acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1A_CONTROL, PM1Acontrol);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
status = acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1B_CONTROL, PM1Bcontrol);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
if (sleep_state > ACPI_STATE_S3) {
/*
* We wanted to sleep > S3, but it didn't happen (by virtue of the fact that
* we are still executing!)
*
* Wait ten seconds, then try again. This is to get S4/S5 to work on all machines.
*
* We wait so long to allow chipsets that poll this reg very slowly to
* still read the right value. Ideally, this entire block would go
* away entirely.
*/
acpi_os_stall (10000000);
status = acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK, ACPI_REGISTER_PM1_CONTROL,
sleep_enable_reg_info->access_bit_mask);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
}
/* Wait until we enter sleep state */
do {
status = acpi_get_register (ACPI_BITREG_WAKE_STATUS, &in_value, ACPI_MTX_DO_NOT_LOCK);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Spin until we wake */
} while (!in_value);
return_ACPI_STATUS (AE_OK);
}
/******************************************************************************
*
* FUNCTION: acpi_enter_sleep_state_s4bios
*
* PARAMETERS: None
*
* RETURN: Status
*
* DESCRIPTION: Perform a S4 bios request.
* THIS FUNCTION MUST BE CALLED WITH INTERRUPTS DISABLED
*
******************************************************************************/
acpi_status
acpi_enter_sleep_state_s4bios (
void)
{
u32 in_value;
acpi_status status;
ACPI_FUNCTION_TRACE ("acpi_enter_sleep_state_s4bios");
acpi_set_register (ACPI_BITREG_WAKE_STATUS, 1, ACPI_MTX_DO_NOT_LOCK);
acpi_hw_clear_acpi_status(ACPI_MTX_DO_NOT_LOCK);
acpi_hw_disable_non_wakeup_gpes();
ACPI_FLUSH_CPU_CACHE();
status = acpi_os_write_port (acpi_gbl_FADT->smi_cmd, (u32) acpi_gbl_FADT->S4bios_req, 8);
do {
acpi_os_stall(1000);
status = acpi_get_register (ACPI_BITREG_WAKE_STATUS, &in_value, ACPI_MTX_DO_NOT_LOCK);
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
} while (!in_value);
return_ACPI_STATUS (AE_OK);
}
/******************************************************************************
*
* FUNCTION: acpi_leave_sleep_state
*
* PARAMETERS: sleep_state - Which sleep state we just exited
*
* RETURN: Status
*
* DESCRIPTION: Perform OS-independent ACPI cleanup after a sleep
*
******************************************************************************/
acpi_status
acpi_leave_sleep_state (
u8 sleep_state)
{
struct acpi_object_list arg_list;
union acpi_object arg;
acpi_status status;
struct acpi_bit_register_info *sleep_type_reg_info;
struct acpi_bit_register_info *sleep_enable_reg_info;
u32 pm1x_control;
ACPI_FUNCTION_TRACE ("acpi_leave_sleep_state");
/* Some machines require SLP_TYPE and SLP_EN to be cleared */
sleep_type_reg_info = acpi_hw_get_bit_register_info (ACPI_BITREG_SLEEP_TYPE_A);
sleep_enable_reg_info = acpi_hw_get_bit_register_info (ACPI_BITREG_SLEEP_ENABLE);
/* Get current value of PM1A control */
status = acpi_hw_register_read (ACPI_MTX_DO_NOT_LOCK,
ACPI_REGISTER_PM1_CONTROL, &pm1x_control);
if (ACPI_SUCCESS (status)) {
/* Clear SLP_TYP and SLP_EN */
pm1x_control &= ~(sleep_type_reg_info->access_bit_mask |
sleep_enable_reg_info->access_bit_mask);
acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK,
ACPI_REGISTER_PM1A_CONTROL, pm1x_control);
acpi_hw_register_write (ACPI_MTX_DO_NOT_LOCK,
ACPI_REGISTER_PM1B_CONTROL, pm1x_control);
}
/* Ensure enter_sleep_state_prep -> enter_sleep_state ordering */
acpi_gbl_sleep_type_a = ACPI_SLEEP_TYPE_INVALID;
/* Setup parameter object */
arg_list.count = 1;
arg_list.pointer = &arg;
arg.type = ACPI_TYPE_INTEGER;
/* Ignore any errors from these methods */
arg.integer.value = 0;
status = acpi_evaluate_object (NULL, "\\_SI._SST", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
ACPI_REPORT_ERROR (("Method _SST failed, %s\n", acpi_format_exception (status)));
}
arg.integer.value = sleep_state;
status = acpi_evaluate_object (NULL, "\\_BFS", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
ACPI_REPORT_ERROR (("Method _BFS failed, %s\n", acpi_format_exception (status)));
}
status = acpi_evaluate_object (NULL, "\\_WAK", &arg_list, NULL);
if (ACPI_FAILURE (status) && status != AE_NOT_FOUND) {
ACPI_REPORT_ERROR (("Method _WAK failed, %s\n", acpi_format_exception (status)));
}
/* _WAK returns stuff - do we want to look at it? */
status = acpi_hw_enable_non_wakeup_gpes();
if (ACPI_FAILURE (status)) {
return_ACPI_STATUS (status);
}
/* Enable BM arbitration */
status = acpi_set_register (ACPI_BITREG_ARB_DISABLE, 0, ACPI_MTX_LOCK);
return_ACPI_STATUS (status);
}
![[BACK]](/icons/back.gif){kind=icon}
Return to hwsleep.c CVS log ![[TXT]](/icons/text.gif){kind=icon}
![[DIR]](/icons/dir.gif){kind=icon}
Up to [Development] / linux-2.4-xfs / drivers / acpi / hardware